{"product_id":"cm-51-kaltentlacker-gel-lackentferner","title":"CM 51 Cold Stripper Gel","description":"\u003cp\u003eCM 51 Cold Stripping Gel quickly and reliably removes even resistant coatings. These include oil, nitrocellulose, synthetic resin and chlorinated rubber paints, interior and exterior dispersion paints, facade paints, sealing paints, fillers, polishes, powder coatings and PU lacquers. According to the data sheet, the effect extends to lacquers baked at 180 degrees Celsius. The technical difference to liquid paint removers lies in the gel form: The product remains on vertical surfaces and profiles, dries out more slowly and keeps the active ingredient in contact with the coating for the entire exposure time of up to 30 minutes. In most cases, one application is sufficient. For businesses, this means short cycle times in component preparation, economical consumption per square meter and the avoidance of thermal or mechanical removal with the risk of component damage. The application range extends from component preparation in metal construction and surface technology to the renovation of facade and interior paints. After removing the old paint, the substrate must be thoroughly cleaned; the clean and dry substrate can be recoated immediately.\u003c\/p\u003e\u003ch3\u003eYour Advantages at a Glance\u003c\/h3\u003e\u003cul\u003e\n\n\u003cli\u003eEffective even on lacquers baked at up to 180 degrees\u003c\/li\u003e\n\n\u003cli\u003eGel form adheres to vertical surfaces and profiles\u003c\/li\u003e\n\n\u003cli\u003eUsually one application is sufficient, exposure time up to 30 minutes\u003c\/li\u003e\n\n\u003cli\u003eRemoves powder coatings, PU lacquers and chlorinated rubber\u003c\/li\u003e\n\n\u003cli\u003eSubstrate can be recoated immediately after cleaning\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\u003ch3\u003eProduct Application\u003c\/h3\u003e\u003cp\u003eApply CM 51 evenly with a solvent-resistant brush and leave to act for up to 30 minutes. Then scrape off the dissolved layer with a spatula or wash off with a high-pressure device and water. For extremely thick layers, a repeated application may be necessary. Paint residues on corners and profiles are best removed with steel wool or a wire brush. After paint removal, the substrate must be thoroughly cleaned; the clean and dry substrate can be recoated immediately. For sensitive surfaces and intensely colored stones and tiles, a preliminary test should be carried out in an inconspicuous area. Do not allow to enter wastewater; observe local wastewater regulations. Wear safety goggles, protect eyes and skin, wash off splashes immediately with water, ensure good ventilation in enclosed spaces. Observe safety data sheet.\u003c\/p\u003e\u003ch3\u003eDosage\u003c\/h3\u003e\u003cp\u003eReady to use, do not dilute. Apply undiluted to the surface to be stripped.\u003c\/p\u003e\u003ch3\u003eConsumption and Coverage\u003c\/h3\u003e\u003cp\u003eThe data sheet indicates a very economical consumption without stating specific values. Experience shows that for gel paint removers, approximately 300 to 500 grams per square meter and application should be assumed, meaning a 10 kg container is sufficient for about 20 to 33 square meters. For multi-layered old paint, calculate accordingly higher.\u003c\/p\u003e\u003ch3\u003eAreas of Application\u003c\/h3\u003e\u003cp\u003ePaint removal from metal components, machine parts, frames and trusses from powder coating, steel constructions, gates and railings, as well as facade and interior paints during renovation work.\u003c\/p\u003e\u003ch3\u003eMaterial Compatibility\u003c\/h3\u003e\u003cp\u003eFor solvent-resistant, strippable substrates. For sensitive surfaces and intensely colored stones and tiles, a preliminary test in an inconspicuous area is absolutely necessary to check material compatibility. Do not allow to enter wastewater; local wastewater regulations must be observed.\u003c\/p\u003e\u003ch3\u003eTechnical Data\u003c\/h3\u003e\u003ctable\u003e\u003ctr\u003e\n\n\u003ctd\u003eProduct Type\u003c\/td\u003e\n\n\u003ctd\u003eready to use\u003c\/td\u003e\n\n\n\u003c\/tr\u003e\u003c\/table\u003e\u003ch3\u003eProduct Comparison\u003c\/h3\u003e\u003cp\u003eCM 51 Cold Stripping Gel (Art. 607) is the thixotropic gel variant of the liquid CM 51 Cold Stripping Agent (Art. 654) and is useful when vertical surfaces or profiles need to be stripped. For mineral substrates and natural stone, WENDRO-GEL (Art. 651) as an alkaline stripping paste is the gentler alternative.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eSale exclusively to commercial customers. All prices net plus statutory VAT.\u003c\/em\u003e\u003c\/p\u003e","brand":"Coverax","offers":[{"title":"11 kg canister","offer_id":58572413895040,"sku":"607-0011","price":183.5,"currency_code":"EUR","in_stock":true},{"title":"33 kg canister","offer_id":58572413927808,"sku":"607-0033","price":507.0,"currency_code":"EUR","in_stock":true}],"url":"https:\/\/coverax.de\/en\/products\/cm-51-kaltentlacker-gel-lackentferner","provider":"Coverax-M-Chemie GmbH","version":"1.0","type":"link"}